Two Kinds of Dressing

Before everyone arrives for our Thanksgiving family gathering, I am making pie crust for the pecan pie, dough for my “famous” cranberry bread, and doing the prep to make Gram’s turkey dressing. Each family is bringing their contributions to the meal (feast). Thanksgiving Day is a flurry of activity with too many cooks in the kitchen—just how we like it! And sitting at the table with the feast before us, we give thanks. Thanks to each other, and to our Creator. We are blessed!

Making perfect pecan pie for Thanksgiving.
Thanksgiving feast prep. It takes two pastry chefs to make the perfect pecan pie.

And before everyone arrives I also manage to sley the reed on the Standard. A different kind of dressing—loom dressing.

Sleying the reed.
Two ends per dent in a 45/10 metric reed.
Sleying the reed.
I sit “inside” the loom on my loom bench to sley the reed.
Next step - tying on!
After the reed is sleyed, I remove the loom bench, lower the shafts, and move the countermarch to the front of the loom. Then, I place the reed in the beater and make sure it is centered. Next step–tying on!
Fresh warp on the back beam. Magical!
Getting dressed. Oh the beauty of a fresh warp going over the back beam! Magical.

A feast for the eyes and hands and heart. Thankful indeed!

May you give thanks,
Karen

Tried and True: Threading Eight Shafts

Threading four shafts is straightforward because the heddles fit perfectly between four fingers and a thumb. Threading eight shafts is tricky because we don’t have that many fingers! Thankfully, threading eight shafts can be as straightforward as threading four shafts. I like to think of it as four shafts in the back, and four shafts in the front.

For a review of threading four shafts, watch the short video in this post: You Can Prevent Threading Errors.

Threading Eight Shafts – Straight Draw

  • Set a small group of heddles apart on each shaft to prepare for threading the next group of ends.
  • Pick up the next threading group of ends and bring it to the front, on the left side of the separated heddles.
  • Lace the threading group of ends under, over, under, over the fingers of your left hand, palm up.
Threading eight shafts - the easy way.
Left hand becomes tensioning device for threading the heddles. I like to put my index finger in between the two parts of the cross, as separated by the lease sticks.
  • Wrap left hand index finger around the group of heddles on shaft one (the shaft nearest the back of the loom), the middle finger around heddles on shaft two, the ring finger around heddles on shaft three, the pinky around heddles on shaft four, and bring the thumb around to hold it all loosely together.
Threading eight shafts - the easy way.
Each warp end is taken in order from between the lease sticks, and then threaded through the heddles in order.
  • Thread the first four heddles—1, 2, 3, 4.
  • With the right hand, hold the group of warp ends taut, and open the fingers of the left hand to release the heddles.
  • Keeping the group of warp ends loosely laced around the fingers, slide the left hand toward you to thread the next four heddles—5, 6, 7, 8. Position your fingers around the heddles on each shaft, as you did for the first four shafts.
Threading eight shafts - the easy way.
Left hand slides toward the front of the loom to thread the next four heddles. It helps to hold the warp ends taut with the right hand while the left hand is repositioned.
  • After threading the second set of heddles, follow the same procedure as before and slide the left hand back again to thread 1, 2, 3, 4.
  • Continue sliding the left hand forward and back, until the threading is completed for that group of ends.
  • Check the threading group for accuracy, and then tie the group of ends together in a loose slip knot.
Threading eight shafts.
Always check for accuracy before moving on to the next threading group.

Complete the threading across the warp. And then, step back and admire the beauty of a beamed and threaded loom.

Glimakra Standard. Threading the loom.
Shafts are raised high for good access and visibility for threading, and for checking for accuracy.
Threading is complete. 8-shafts undulating twill.
Threading is complete. Cotton throw. 8/2 cotton, undulating (wavy) twill on eight shafts.

May you find efficient methods for the work of your hands.

Happy weaving,
Karen

Getting Dressed to Weave

I want to wrap up in this cozy throw already. But I need to weave it first. This is an undulating twill throw that I am making for sweet Lindsay, one of my daughters-in-law. Of course, I am including enough warp to make a small throw of my own.

Getting ready to beam the warp. Back to front warping.
Four chained bouts. The 8/2 cotton warp is pre-sleyed, and the back tie-on bar has been placed through the loops at the end of the warp.

Every step of dressing the loom is fascinating. I easily get immersed in the enjoyment of the process. All the while, I’m dreaming of the finished work.

Read to beam the warp, using warping trapeze.
Warping trapeze is in place at the front of the loom. Ready to beam these soothing colors onto the warp beam.
Warp is beamed. Ready for threading.
Warp is beamed. Warp ends are counted into groups of 32 ends each, for efficiency and accuracy in threading. This will be threaded for undulating twill on eight shafts.

Dressing the loom leads to the making of cloth. Dressing our lives leads to the making of good character. Prayer is of utmost importance in dressing our lives. Prayer is not a single step in the process, but a posture of faith throughout the process. Earnest prayer reaches God. The power of prayer is not in our words, in the threads we express, but in the Grand Weaver. He receives our humble threads and weaves them into his will to bring about his beautiful cloth. Fascinating, isn’t it?

May you dream as you dress the loom.

Prayerfully,
Karen