Tag: quick tip

Tried and True: Just in Case

Karen

Texsolv cord is ingenious! It suspends shaft holders while I dress the loom. It also suspends the heddling bar during drawloom setup. A small anchor pin or arrow peg does the trick of holding everything together.

How to use Texsolv cord and anchor pins.
Anchor pin is buttoned through the Texsolv cord and placed into the hole at the bottom of the shaft holder.
Talking about Texsolv cord and arrow pins.
Thread one end of the Texsolv cord through a hole in the other end to make a loop. Insert an arrow peg through a hole to secure the loop.

But there is one potential hazard…

In order to adjust the height of the suspended heddling bar at the drawloom, I want to move the arrow peg. I hold one end of the bar while pulling the peg out of the Texsolv cord. That little peg fumbles out of my hand and drops to the floor. OOPS! I am left holding one end of the bar that has 148 threaded pattern heddles, weights included. Now what?! Alone in the room, I am now the sole support for that end of the heavy bar. The peg on the floor is out of reach.

Super Simple Tip of the Day

Always keep a spare anchor pin or arrow peg on the loose end of the Texsolv cord. Always.

Just in Case strategies.
Spare anchor pin stays on the shaft-holder cord. You do not want to be left holding a shaft holder with eight shafts if your anchor pin ever falls out of your hand…

The rest of the story…
When that pesky little arrow peg slips out of my hand I calmly take the spare peg that is there “just in case,” and secure the Texsolv loop that holds the heddling bar. No big deal, after all.

Strategies for Just in Case!
Spare arrow peg dangles below. Whew!
Tips for just in case!
Spare arrow peg is a life saver on the rare occasion it is needed. There is a significant amount of weight on that heddling bar.

May you be ready for anything, just in case.

Ready or not,
Karen

Tried and True: Five Steps for Rag Rug Selvedges and a Quick Tip Video

Karen

What do you look for in a handwoven rag rug? How do you detect quality of craftsmanship? I look at the selvedges. First thing. I look for selvedges that are nice and tight, and that have a uniform twist at the edge. A few simple steps, consistently practiced, produce the kind of quality you can see and feel. It’s one more reason I find delight in weaving rag rugs.

Rag rug selvedges. Short quick tip video.
Rag rug selvedges. Weft is snugly wrapped around the selvedge warp ends.

Five Steps for Firm Selvedges on a Rag Rug

  1. Throw the shuttle, leaving a loop of the fabric-strip weft at the selvedge.
  2. Hold the weft out taut, and turn the weft under twice at the selvedge.
  3. Untwist the weft in the shed, straightening it, as needed.
  4. Pull the weft tight against the selvedge.
  5. Position the weft in the shed and beat it in.
Weaving a rag rug. Tutorial video of a quick tip.
Beater swings forward to beat in the weft with its just-formed firm and tidy selvedge.
Filming a short video on weaving rag rug selvedges.
Set up for filming the short tutorial. My husband does the filming and proves his patience through several retakes.

Watch this Quick Tip video for a short demonstration.

Rag rug on the loom. Tutorial about selvedges.

May the quality of your work be the first thing noticed.

Happy Weaving,
Karen

Tools Day: Band Loom Warping Board

Karen

It is almost effortless to make a short warp for the band loom. All you need is a peg at the beginning and a peg at the end. You can use a spoke of the warp beam wheel, for instance, at one end, and the leg of an upside-down stool at the other. I normally use my warping reel, though, for even a simple warp, because the reel is so handy. However, I don’t have my warping reel here at the apartment, so I am turning my band loom into a handy warping board for this band loom project.

Using the Glimakra band loom as a warping board.
Using the Glimåkra band loom to measure a narrow cottolin warp.

How to Use the Band Loom as a Warping Board

Tools and supplies:

  • Glimåkra band loom
  • Thread for weaving a narrow band
  • Basket and/or spool holder(s)
  • Scissors

How to use the band loom as a warping board.
Starting at one peg and ending at another. The band loom becomes a simple tool for winding a short warp.

For a warp of approximately two meters:

  • Put the warp thread on the floor below—quills in a basket, and/or thread tubes on spool holders.
  • Using two or more ends, tie the ends together with an overhand knot. (I used three ends together for this warp.)
  • Bring the warp ends up around the warp beam and over the back beam.
  • Loop the knot on the starting peg.
  • Draw the ends from the starting peg to the ending peg, around the band loom, following this path:
  1. Starting peg–upper heddle peg nearest back beam
  2. Lower heddle peg nearest back beam
  3. Back beam
  4. Warp beam
  5. Cloth beam
  6. Front beam
  7. Lower heddle peg nearest front beam
  8. Ending peg–upper heddle peg nearest front beam
  • Follow the winding path in reverse order back to the starting peg.
  • Continue winding until you have reached the desired number of ends.
  • Cut the ends and tie off at the starting peg or the ending peg.
  • Tie one or two choke ties, if needed. (I didn’t need them for this short warp.)
  • Carefully remove the warp and dress the band loom as usual. (For a tutorial on dressing the band loom, click here: Quiet Friday: Band Loom Warping and Weaving.)
  • Weave to your heart’s content.

Weaving hanging tabs for towels on my Glimakra band loom.
One meter of woven band is cut off. The remaining band warp is tied back on. Weaving can resume at any time.

Preparing to sew handwoven ribbons onto handwoven towels for hanging.
Ends secured, and cut in 10.5 cm lengths, the tabs are ready to be sewn onto the double weave towels.

May you find tools you didn’t know you had.

Happy band weaving,
Karen

Halfway Milestone

Karen

Halfway is a milestone when you are threading 2,064 ends. This double weave in two blocks has threading such that I can listen to podcasts without losing my place. It’s a long stretch to the halfway point.

Threading heddles, from right to left.
Threading heddles, going from right to left.

Before threading, I find the center of the warp and the group of ends that are just past center. I drape those ends on the back beam to mark the spot.

Threading 2064 ends. Halfway point is identified.
Center of the warp is identified. The ends just left of center mark the spot.

Threading heddles in my "playhouse" in the loom.
Sitting in my playhouse to thread the heddles. No hurry.

I’m excited to reach halfway in the threading! It’s a turning point. Now, while they are readily accessible, I position all of the shaft-to-lamm cords to hang down, right at the center of the warp where they belong.

Halfway finished threading heddles! Only 1,032 to go. :)
Half of the threading work is done! Only 1,032 ends to go. 🙂

Cords aligned at the center of the warp.
Center of the warp. Good time to align the cords that go from the lower shaft bars to the upper lamms.

Threading heddles for double weave on a Glimakra Standard loom.
Threading for the double weave throw continues, a few minutes here, an hour there, until all the ends are in heddles.

Have you ever reached a turning point in life, and knew it was time to position things? We try to be good and loving. But we’re never as good as we think. And we end up loving only the people we want to love. We have been separated from God. Our misdeeds push us away from him. Easter is resurrection, but before that is the cross of Christ. God so loved us that he closed the separation between us and him with the cross. That’s the turning point he offers to us, to set things right. Our part is to believe.

May you look forward to the second half.

With you,
Karen

Three Rosepath Rag Rugs For Now

Karen

There are three completed rosepath rag rugs on the loom, with warp remaining for at least one more rug. Since I don’t know how soon I will be able to weave the remainder, cutting off the completed rugs makes sense. After hemming, I will have three new rugs for Etsy. (Don’t miss the new Quick Tip video at the end of this post!)

Cutting off rosepath rag rugs, with some warp remaining to be woven.
As the warp ends are cut, they are tied into one-inch groupings to simplify tying back on to the tie-on bar.

Unrolling some new rosepath rag rugs!
Warping slats are used as spacers between rugs. Some of my slats are barely wide enough for this warp.

I look forward to full weaving days again, with both looms dressed, and shuttles zooming. That rag rug warp still on the loom will be a reward worth waiting for.

Rosepath rag rug ready to be hemmed. Karen Isenhower
One rug has warp end knots, and is ready for pressing and hemming.

Two rosepath rag rugs just off the loom. Karen Isenhower
Rosepath in two variations.

Rosepath rag rug ready to be hemmed. Karen Isenhower
Broad rosepath pattern lends elegance to this rag rug.

Last week, when I awoke from surgery, the relentless pain I had been experiencing in my left leg and lower back was gone. Completely gone! It made me think of heaven. Ancient writings tell us that the lame will leap like a deer, and that sorrow and sighing will flee away. There’s no place for pain in heaven. All the people there have been healed and restored. That’s a reward worth waiting for. And I won’t be surprised if there are at least a few in heaven who are weaving away to their heart’s content.

May you know what to do while waiting.

Wishing you well,
Karen