Category: Tried and True

Tried and True: When the Shed is Missing

Karen

You followed all the instructions for dressing the loom, and have finished the countermarch tie-up. Now, at the moment of triumph you step on the treadles, one by one. Alas! Some or all of the treadles give you nothing you can call a shed. Now what? Maybe you relate to Laura who wrote me recently, “I can’t seem to get the treadles to make a shed.”

The solution is simple. Follow the advice in this sentence on page 37 of Learning to Warp your Loom, by Joanne Hall, “If your sheds are not good, check your loom tie-up from the top down.”

If sheds are missing, there is a good chance you have a crossed cord.

Warp is threaded, sleyed, and tied on. After arranging and connecting a few Texsolv cords, I will tie up the treadles.

Find Misaligned Cords

1 Follow each Texsolv cord, starting from the countermarch at top of the loom.

All the shafts are good to go, right? Not quite. Better see what’s happening at the top of those Texsolv cords.

2 Make sure that each cord is connected in the right order at the right place.

Is the first countermarch jack connected to the first shaft, the second jack to the second shaft, and so on?

Misaligned cords as seen from the top of the loom.

Are the cords that go to the lower lamms strictly in order?

– With horizontal countermarch, does each cord fall behind the shafts in order?

Cords from the horizontal countermarch go through the center of the warp, to be attached to lower lamms below.
Make sure each cord goes behind its corresponding shaft bars to the lamms below. When attaching the cords to the lamms, make sure the cords are attached in the correct order. If loom is already tied up, follow each cord to check that it is attached to its corresponding lamm.

– With vertical countermarch, is each cord on its pulley, and connected to lamms in the right order?

Vertical countermarch has cords that go over pulleys on the side down to the lower lamms. I have to be extra careful to keep from attaching a cord to the wrong lamm.

3 Correct any misaligned cord.

Now, step on each treadle, one by one. Decent sheds that just need a little refining? Triumph!

Helpful Habit

When attaching a cord while dressing the loom, start your hand at the top of the cord and slide it down to the point of connection. This helps you take hold of the correct cord.

Ready to connect the shaft cords on the Glimåkra Julia, made easy by the small hooks on the shaft bars. Instead of expecting the cords to hang straight down in order, I reach my hand up to the top of the cord.
Touching where the cord meets the wood, I know I have the correct cord for the shaft closest to the front of the loom. I do the same for the next cord.
My hand slides down the cord and I connect the cord to the correct shaft. Now, all that’s left is tying up the treadles. Then, we weave!

May none of your cords be crossed.

Happy Weaving,
Karen

Tried and True: Rag Rug Block Party!

Karen

I am happy to say that with only four shafts we have exactly what we need for a checkerboard rag rug. Thank you to Megan for asking about it. ”I am searching for a 4-shaft draft for a checkboard pattern. I am limited to only 4 shafts.” Double binding opens up a world of opportunity!

Checkered rag rug. Karen Isenhower

Let’s talk about blocks. A block is a specific sequence of warp ends or weft picks. Double binding on four shafts has two blocks for the warp and two blocks for the weft.

One of several possible threading and tie-up plans for double binding. Add two plain weave treadles if you want to weave plain weave hems.
Plain weave hem starts a new double-binding rag rug.

Have a Block Party!

→ Use graph paper to plan the configuration of your blocks.

For the threading blocks, use two rows of squares. One row is for Block A and one row is for Block B. Each square on the paper represents one threading unit. You can make a checkerboard pattern by uniformly alternating the A blocks and B blocks. Or, you can make a wildly different geometric pattern by varying the size of alternating blocks. Your two-row graph becomes a profile draft to use as your threading key.

For the weft blocks, use the same arrangement of blocks as for the threading, and turn them vertically for the treadling draft. Or, use your creativity to make a unique configuration of weft blocks. The sky is the limit!

Three possible block configurations for the threading. The bottom example is a part of the sequence for the rug currently on my loom.
Weaving with two ski shuttles. Glimåkra Ideal. 4 shafts, 6 treadles.
Printout shows me where the blocks change in the weft.

Check out these resources for more double-binding rag rug ideas: Alla Tiders Trasmattor, by Monica Hallén and Ann-Kristin Hallgren; Så Fint med Trasmattor, by Monica Hallén and Ann-Kristin Hallgren; Älskade Trasmattor att väva som för, by Monica Hallén and Ann-Kristin Hallgren; Swedish Rag Rugs 35 New Designs, by VävMagasinet; Happy Weaving, from VävMagasinet.

May you discover a world of opportunity.

Happy Weaving,
Karen

Tried and True: Measurement Tape

Karen

You can measure what you are weaving. A set of towels will all be the same length. A table runner will fit the table as planned. A rug will be the right size for the designated floor space. All it takes is a dependable way to measure. (Thanks to Elisabeth S. for writing me, “I’d love to have a better way to measure my work as I’m weaving it.”)

Dependable way to measure on the loom!

Measurement Tape (accompanying video below)

Supplies:

  • Calculator
  • Project notes
  • 5/8” polyester twill tape
  • Fine point indelible marker
  • Tape measure
  • 2 flat-head straight pins

Make Calculations

  • Determine the finished length.
    • Consider the Golden Ratio, 1:6.
    • Consider where the finished textile will be placed.
  • Estimate take-up and shrinkage.
  • Include these measurements in your project notes.

Prepare a Measurement Tape

  • Draw the beginning line about 2 cm from the end of the tape. If there is a hem, draw a second line to mark the hem’s length.
  • Write the item description on the tape.
  • Write ” ___ (finished length) + ___ (take-up and shrinkage) = ___ (total length)” on the tape.
  • Measure the total length from the first line (or from the hem) on the tape. Draw a line at the end (add hem, if needed).
  • Cut the tape about 2 cm after the ending line.
  • Find the middle of the tape. Draw a line and write “MID”.
How to measure your weaving on the loom.
Place the first line of the measurement tape directly over the beginning picks of the woven article.

Prepare a Half Measurement Tape

  • Do the same as for a full-length measurement tape, except divide the total length measurement in half. Draw a line on the tape at the halfway point. Write “MID” before the line.
  • Cut the tape about 2 cm after the MID line.

Weave and Measure (Always with the warp under tension)

  • Use two straight pins to pin the measurement tape to the weaving near one selvedge. Place the beginning line of the tape directly over the beginning of the woven article.
  • As weaving progresses, remove the pin closest to the breast beam. Leapfrog over the remaining pin. Reinsert the removed pin through the tape near the fell line.
Using a measurement tape for weaving consistent lengths.
Move one pin at a time. I usually move the pin right before I advance the warp.
  • If using a half measurement tape, weave past the MID line. Mark the spot with a pin. Remove the measurement tape. Turn the tape and pin into place to weave the second half.
How to make a half measurement tape.
When you reach the MID line on a half measurement tape, keep the measurement tape in place until you have woven a few more centimeters.
How to make and use a Measurement Tape for weaving accurate lengths.
Place one pin through the cloth, pointing to the MID line. Then, it’s safe to remove the measurement tape and turn it around. Go your merry way, weaving the second half of the Monksbelt runner, or whatever you have on your loom.

Here’s a demonstration of making and using a measurement tape:

(For a previous discussion of this topic, see Tools Day: Measured Weaving.)

Since you can measure what you are weaving, do relax and enjoy the ride.

May you reach the mid point at just the right time.

Happy Weaving,
Karen

Tried and True: Prevent Weaving Mistakes with Two Secret Weapons

Karen

As much as I am enthralled with what I am doing at the loom, my concentration ability wanes. It is in those waning moments that errors happen. Also, as you know, I have looms in my home, which means I can weave well into the evening in my pajamas, if I want to. But, I better not exceed my limits, or else…

Combination drawloom. Towels for gifts.
Seven pattern shafts are being used for the border “windows.” The center area uses single units to make the design that includes numerals and letters.

Weaving on the drawloom demands my undivided attention, as does pictorial tapestry and any intricate pattern weave. All of these are especially tedious to undo. Therefore, mistakes are outlawed! To that end, I have two secret weapons that prevent all most mistakes—

Combination drawloom for weaving towels.
Same towel, same weft, same time of day as previous picture. A change of viewing angle highlights the rust in the brown-rust 16/1 linen weft. I notice things like this when I get up and take a break.

Five-Minute Breaks

Twenty-Five Minutes On – Five Minutes Off

25 Minutes. Go full strength. Be completely absorbed in the task.
5 Minutes. Take a break. Stand up, walk around, stretch.
(I use an app on my phone, Focus Time Activity Tracker, but any timer will do.)

The Cinderella Hour

Know When to Stop

If I am weaving at the end of the day (in my pajamas, or not), I stop when the clock chimes 8 times. I call it my Cinderella hour. My loom turns into a pumpkin after 8:00 pm. If I keep weaving, I can expect to be fixing errors the next day.

Weaving in the evening in my pj's. Monksbelt.
Weaving monksbelt in the evening (in my pajamas). Oh listen, I hear the clock chiming…1.2.3.4.5.6.7.8. Time to put the shuttles down.

May you know when to take a break.

Happy Restful Weaving,
Karen

Tried and True: Weft Rep

Karen

The monksbelt piece that adorns our entry is my favorite from all the projects in The Big Book of Weaving, by Laila Lundell. This current narrower version on the Standard is another heirloom monksbelt piece in the making. The ground cloth is weft rep.

Classic monksbelt in modern colors.
Multi-color ground weave and vibrant Fårö pattern colors make this monksbelt fabric a standout. Glimåkra Standard in the background holds a new version of this favorite piece.

This is snail’s-pace weaving, with 2 picks of 16/2 cotton for the ground weave between every 6/1 Fårö wool pattern pick.

“To weave [weft rep]…the weft must be longer than the width of the warp and so the weft has to arc across the shed. There are two ways to do this: with many small waves across the width or with a large and high arc…The tiniest bit of unevenness can quickly build into hills and valleys across the weft line…”

The Big Book of Weaving, p. 236

Weft Rep in Three Steps

1. Make a Mountain.

After throwing the shuttle, increase the length of the weft by making it into a large arc in the open shed. Put one finger through the warp to form the peak while keeping enough tension on the thread with your other hand to maintain a good selvedge.

Weft rep tutorial
Weaving monksbelt with weft rep. How to.

2. Make Hills and Valleys.

Keeping the shed open, push the mountain down into hills and valleys to evenly distribute the extra weft.

  • Turn the mountain into hills and valleys with your finger.
Monksbelt with weft rep. Tutorial.

OR,

  • Simply drag your spread-out fingers lightly through the weft.
Weft rep how to.
Monksbelt with weft rep. Tutorial.

OR,

  • TIMESAVER – Slowly pull the beater toward you (shed open), smooshing the weft into a wavy line. Stop two or three inches away from the fell line.
Weft rep using the beater to make wavy line.
Simplified weft rep.

3. Flatten the Hills

Treadle for the next shed. On the closed shed beat in the weft. Two short pulses with the beater distribute the weft more effectively than a single squeeze with the beater.

Simplified weft rep.

Watch for little loops that may form in places where there is a bit too much weft. To correct, open the shed, pull that portion of the weft back into a little hill and redo.

OR,

  • TIMESAVER – Draw the back of your fingernail across the warp where you see excess weft. This is often enough to even out little bumps.
Weft Rep - How to, and simplified.

Slower weaving develops into a rhythmic pace that is comfortable. And the cloth grows, line by line.

Monksbelt on the Glimakra Standard.
Rows of monksbelt flowers.

May your slow pace yield thoughtful progress.

Slowly and Surely,
Karen