Process Review: First Drawloom Warp

There are two questions I hear most often. 1. How long did it take? 2. What is it going to be? These are hard questions to answer. I admit that I stumble around to find satisfying answers. 1. How long? Hours and hours. 2. Cloth. It is going to be cloth. What will the cloth be used for? I don’t know. But when I need a little something with a pretty design, I’ll know where to find it. There are two finished pieces, though, from this first drawloom warp: the Heart-Shaped Baskets table runner (adapted from a pattern in Damask and Opphämta, by Lillemor Johansson), and a small opphämta table topper that I designed on the loom. The rest are samplers, experiments, tests, and just plain fun making-of-cloth. Oh, and I wondered if I could take the thrums and make a square braid…just for the fun of it.

First warp on my drawloom. Success!
Opphämta piece on the left, with Fårö wool pattern weft. Heart-Shaped Baskets runner on the right, with red 16/2 cotton pattern weft. Ten pattern shafts.

I will let the pictures tell the story of this first drawloom warp.

May you have plenty of things to make just for fun.

Happy Weaving,
Karen

All the Looms

The plan to keep every loom dressed is easy when there is only one loom. Now that I have four floor looms, it’s a tough plan to follow. The drawloomcheck. The Glimåkra Standard, dressed in Tuna wool—check. The two smaller looms are threaded, and just need tying on and tying up. So, I’m well on my way! The end of the first warp on the drawloom is in view, however. That means the drawloom will soon be back in the queue. And so it goes.

Winding a warp for rosepath rag rugs. 12/6 cotton. Spring colors.
Winding a warp for rosepath rag rugs. 12/6 cotton. Spring colors.
Warp for cottolin towels.
Warp for cottolin towels is threaded on the little hand-built loom.
Opphämta on the drawloom.
Opphämta on the drawloom. Pattern weft is 6/1 Fårö wool. The right side of the fabric is seen underneath, as it comes around the breast beam.
Threading heddles on the Glimåkra Ideal.
Threading heddles on the Glimåkra Ideal.
Blue and Almond Tuna wool warp.
Blue and Almond Tuna wool warp is tied on in 1″ sections.

I like to stay a step ahead of my looms. I’m ready to wind a new warp as soon as I finish cutting off. It’s the cycle of weaving. But I have trouble staying ahead.

Tying up treadles on the Glimakra countermarch.
Twelve shafts. Twelve upper lamms. Twelve lower lamms. Twelve treadles. This is an amazing system.
Warp is tied on. Ready for rag rugs!
Warp is tied on. Ready to add the leveling string.
Loom is dressed for small wool double weave blanket.
Loom is dressed. Treadle cords are adjusted. Ready for weaving!
End of warp on the drawloom.
End of warp comes near the pattern heddles. This is my first drawloom warp, so I’m waiting to see how far I can weave until I lose a good shed. So far, so good.
My first drawloom warp.
Closing chapter of my first drawloom warp. I’ll keep “turning pages” until the shed disappears.

We have good plans for our lives. But often, it’s tough to follow those plans. Too many things happen at once, and we don’t know how to stay ahead of it all. The thing to remember is that our plans stem from our inner commitments. When we commit our ways to the Lord, trusting him, he leads us through our days. Trust turns plans into achievements. And those are the plans worth pursuing.

May your best plans succeed.

Happy Weaving,
Karen

Tried and True: Center the Reed

Eleven hours and thirty-six minutes into this project, the starting line for weaving is just around the corner. Wind the warp, and beam it. Thread the heddles. Sley the reed. Unlock the back beam ratchet. Move the countermarch to the front of the loom. … Pause when you think about moving the twelve shafts and the reed forward with the countermarch. Reach. Wiggle. Pull. Wiggle. Pull some more. Got it. Now, put the reed in the beater. Relax? Almost, but not yet.

Time to move the whole shebang forward.
Reed is sleyed, so reed support cords have been removed. Time to move the whole shebang forward.
Ready to insert the reed into the beater.
Plastic-coated wire is threaded through the ends of the shaft bars because I don’t have shaft pins long enough for twelve shafts. After coaxing and wiggling the mass of shafts forward, with the countermarch above them, I am ready to insert the reed into the beater.
Basics: How to center the reed.
As I put the reed in the beater I make sure all of the ends are free, and not trapped in the beater’s grip.

We must not forget to center the reed. I center the reed just as soon as the reed is in the beater.

How to Center the Reed

(We are actually centering the warp that is in the reed.)

Supplies needed: Tape measure (or string)

1. Using the tape measure, measure from the right edge of the warp in the reed to the outer edge of the beater on the right-hand side. Hold the tape measure with your fingers marking the measurement.

Center the reed.


2. Holding that measurement, place the tape measure at the left edge of the warp in the reed stretching out toward the outer edge of the beater on the left-hand side.

How to center the reed.


3. Note the difference in measurement between the right side and left side. Move the reed in the beater to center.


4. Repeat the first two steps until the measurements are the same on both sides.

Centering the reed.
Tips for centering the reed in the beater.
Tips for centering the reed in the beater.
Reed is centered.

Now you can relax. Enjoy the moment, because you are that much closer to seeing fabric take shape!

May you enjoy the process you’re in.

Patiently,
Karen

Weaving Hearts

Pulling the draw handles for each four-thread unit of weaving is like doing counted cross stitch on the loom. I enjoyed cross stitch in the 1980’s and I am enjoying this drawloom version now. Very much. I started this Heart-Shaped Baskets table runner on Valentine’s Day—a fun way to celebrate the day!

Heart-Shaped Baskets. Adapted from pattern in Damask and Opphämta, by Lillemor Johansson.
Heart-Shaped Baskets. Adapted from a pattern in Damask and Opphämta, by Lillemor Johansson.
Drawloom hearts.
Red 16/2 cotton weft on unbleached 16/2 cotton warp. The dark weft on a light warp makes consistency in beating that much more important.

Like weaving on any floor loom, I want to have consistency in my beat and in my selvedges. Inconsistencies in these basics can detract from the drawloom imagery of the final cloth. The main thing is to keep paying attention. And keep joyfully pulling those draw handles to create more hearts of love.

Drawloom hearts.
Stripes at the edges prove to be a challenge for getting consistent selvedges.
Table runner on the drawloom.
Table runner is woven in broken twill on four ground shafts, with eleven pattern shafts.

Grace is a gift of favor, not an earned reward. Forgiveness is the giving of grace. And gratitude results from receiving grace. Grace makes us graceful. Giving and receiving grace with consistency is what we’d like to see in ourselves. That’s when the love of God, in whose image we’ve been made, is most clearly seen in us. So we practice what we know to do. And pay attention. And keep joyfully weaving a heart of love, by God’s grace.

May you be grace – full.

Gratefully yours,
Karen

Beaming Double Weave

This is double weave on twelve shafts. One layer is the gorgeous lapis lazuli blue. The other layer is neutral almond for contrast. I am spreading and beaming this 6/2 Tuna wool warp with two sets of lease sticks—one set for each layer/color.

Big fat warp chains. Tuna wool for double weave.
Big fat warp chains. Double weave on twelve shafts, with 6/2 Tuna wool for warp and weft.

When you have two sets of lease sticks, though, it is a serious challenge to get the two colors to alternate correctly as you move the end loops to a separate stick. The ends on the stick are then transferred to the back tie-on bar. I did breathe a sigh of relief when everything was finally lined up and in order.

Double weave. Ready to beam the wool warp.
Two sets of lease sticks carries the challenge of having clear visibility of the lease cross in both warp layers. After one or two do-overs, all the yarn is successfully moved to the back tie-on bar. Moving from right to left, I separate and straighten each warp end on the tie-on bar. Only a few more left to straighten.
Ready to beam this wool double weave warp.
Back tie-on bar all in order. Now ready to move the pre-sley reed to the beater and begin beaming the warp.

And I’m reminded again how beautiful a beamed warp is. It’s worth the challenges.

Tuna wool warp on Glimakra Standard.
Warp beam and back beam show the beamed warp.
Wool warp separated into threading groups.
Separated into threading groups for the next phase of dressing the loom.

That beautifully ordered wool on the back tie-on bar, now hidden from view, is an essential element for quality handwoven cloth. Kindness is that way. It’s a core trait deep in one’s character that is revealed in interactions with others. Kindness makes you beautiful. It’s not something you try to be. It’s something we wear. It’s our inner being dressed in the character of Christ.

May you be dressed in kindness.

Affectionately yours,
Karen