Process Review: Casita Tapestry

This little Casita travel trailer is a good symbol of the retirement phase for Steve and me. I started the tapestry a few months before our move to Texas hill country, in anticipation of our new adventures. And then, the day after Steve retired we went to Rice, Texas and drove away with our new Casita La Perlita (Little Pearl), as if to say, “Let the adventure begin!”

Just off the loom - "La Perlita" Casita tapestry.
Just off the loom, La Perlita Casita. 37 cm x 26 cm (14 1/2″ x 10 1/4″)

Enjoy the Casita tapestry review.

May your adventures come at just the right time.

Happy journeying,
Karen

Process Review: First Drawloom Warp

There are two questions I hear most often. 1. How long did it take? 2. What is it going to be? These are hard questions to answer. I admit that I stumble around to find satisfying answers. 1. How long? Hours and hours. 2. Cloth. It is going to be cloth. What will the cloth be used for? I don’t know. But when I need a little something with a pretty design, I’ll know where to find it. There are two finished pieces, though, from this first drawloom warp: the Heart-Shaped Baskets table runner (adapted from a pattern in Damask and Opphämta, by Lillemor Johansson), and a small opphämta table topper that I designed on the loom. The rest are samplers, experiments, tests, and just plain fun making-of-cloth. Oh, and I wondered if I could take the thrums and make a square braid…just for the fun of it.

First warp on my drawloom. Success!
Opphämta piece on the left, with Fårö wool pattern weft. Heart-Shaped Baskets runner on the right, with red 16/2 cotton pattern weft. Ten pattern shafts.

I will let the pictures tell the story of this first drawloom warp.

May you have plenty of things to make just for fun.

Happy Weaving,
Karen

Tried and True: Center the Reed

Eleven hours and thirty-six minutes into this project, the starting line for weaving is just around the corner. Wind the warp, and beam it. Thread the heddles. Sley the reed. Unlock the back beam ratchet. Move the countermarch to the front of the loom. … Pause when you think about moving the twelve shafts and the reed forward with the countermarch. Reach. Wiggle. Pull. Wiggle. Pull some more. Got it. Now, put the reed in the beater. Relax? Almost, but not yet.

Time to move the whole shebang forward.
Reed is sleyed, so reed support cords have been removed. Time to move the whole shebang forward.
Ready to insert the reed into the beater.
Plastic-coated wire is threaded through the ends of the shaft bars because I don’t have shaft pins long enough for twelve shafts. After coaxing and wiggling the mass of shafts forward, with the countermarch above them, I am ready to insert the reed into the beater.
Basics: How to center the reed.
As I put the reed in the beater I make sure all of the ends are free, and not trapped in the beater’s grip.

We must not forget to center the reed. I center the reed just as soon as the reed is in the beater.

How to Center the Reed

(We are actually centering the warp that is in the reed.)

Supplies needed: Tape measure (or string)

1. Using the tape measure, measure from the right edge of the warp in the reed to the outer edge of the beater on the right-hand side. Hold the tape measure with your fingers marking the measurement.

Center the reed.


2. Holding that measurement, place the tape measure at the left edge of the warp in the reed stretching out toward the outer edge of the beater on the left-hand side.

How to center the reed.


3. Note the difference in measurement between the right side and left side. Move the reed in the beater to center.


4. Repeat the first two steps until the measurements are the same on both sides.

Centering the reed.
Tips for centering the reed in the beater.
Tips for centering the reed in the beater.
Reed is centered.

Now you can relax. Enjoy the moment, because you are that much closer to seeing fabric take shape!

May you enjoy the process you’re in.

Patiently,
Karen

Process Review: Comfy Throw With Fringe

This throw has fringe. It seems appropriate for a homestyle cotton wrap. Fringe says comfortable, casual, and playful. I do not mind the time it takes to twist the threads to make this tactile edging. It’s a satifying close to a worthwhile project. After all, who can resist running their fingers through soft twisted fringes?

Finished handwoven cotton throw.
Knots on the ends of the fringes are trimmed off after washing and drying the throw.

Reminisce with me through the start-to-finish process of making this eight-shaft undulating twill throw for my lovely daughter-in-law Lindsay.

Beaming the warp.
Dressing the Great Room loom.
Heddles are threaded.
Sleying the reed on Glimakra Standard.
Ready to tie on.
Eight shafts.
All tied on.
Testing, testing...
Eight-shaft undulating twill in 8/2 cotton.
Cloth beam is filling!
Weave to the end mark.
Hemstitching at the end of the cotton throw.
Playing with pattern. 8-shaft twill.
End of warp is near.
8-shaft twill. Fun with patterns.
Cutting off!
Getting ready to twist fringe.
Twisting fringe on cotton throw.
Before wet finishing.
After wet-finishing.
Trimming off the knots at the end of fringes.
Finished 8-shaft twill cotton throw. With fringe!

May you have plenty of fringe benefits.

Happy Weaving,
Karen

Weaving History Carries Memories – Year in Review Video

Transition. Changes. Adventure into the unknown. That describes 2018 for Steve and me. When I review my weaving history for the year, everything on the loom is attached to a memory. Like an old song that awakens our thoughts to past experiences, the Lizard tapestry certainly sparks in me revived memories of our transition season and the moving of looms. See Quiet Friday: Tapestry in Transition.

Removing the warp beam. Relocating the loom.
Steve unscrews a bolster that holds one side of the warp beam so I can remove the warp beam.

I began 2018 with a plan to weave coordinated fabrics for our Texas hill country home—towels, upholstery for bar stools, and placemats, explained in this post: Harmonized Weaving for the New Year. Accomplished! I also committed to weaving a gift for each of my three daughters (daughter and two son’s wives), as described in this post: Weaving a Gift. Accomplished two out of three! The final gift is nearing halfway on the loom right now.

Hemstitching at the beginning of the cotton throw.
Cotton throw has hemstitching at the beginning. The ends will be twisted for fringe when it’s taken from the loom.

Eight-shaft twill in an undulating pattern. Lightweight cotton throw.
Eight-shaft twill in an undulating pattern. Single-shuttle weaving gets me off to a fast start for 2019.

2019 is a continuation of transition, changes, and adventure, as we tiptoe into this retirement chapter. A drawloom is in the forecast, as well as some travel tapestry weaving, and more rag rugs, towels, scarves, and throws. And anything else we can think up. It’s going to be a good year! Thank you for coming along. I’m grateful to have you as a friend.

May you have much to look forward to.

Blessings to you,
Karen